Welcome To b2b168.com, Join Free | Sign In
中文(简体) |
中文(繁體) |
Francés |Español |Deutsch |Pусский |
| No.13636401

- Product Categories
- Friendly Links
Information Name: | Aeration Head |
Published: | 2015-07-24 |
Validity: | 365 |
Specifications: | |
Quantity: | 2000.00 |
Price Description: | |
Detailed Product Description: | [Introduction] membrane diffusers is a new aeration equipment aeration device consists of aeration, regulators, countersigned member and cloth trachea children road, three, four, elbow pipe fittings to connect components. It satisfied all the aeration tank, there is substance of contact with oxygen pool of life, there is substance to life in prison stabilization ponds place. Membrane diffusers press for pool shaped seating-density, aerator and cloth trachea children said that the use of appropriate and G3 / 4 countersigned turnbuckle, turnbuckle within the base (fixed in the cloth tube children run), aeration outer turnbuckle. When installed, the first regulator desired size is fixed to the bottom, and then use the cloth tube hoop fixed to the child channel regulator. The main unique place is child bubble diameter is small, the average bubble child profile sheets, strong corrosion resistance. [Product Parameters aerator Size: 260mm, 215mm Service Area: 0.35-0.75m2 / a, 0.25-0.55m2 / a running average pore membrane aeration: 80-100 micron air flow: 1.5-3m3 / a h oxygen transfer coefficient: kla (20%) 0.204-0.337min-1 oxygen utilization :( depth 3.2m) 18.4-27.7% oxygenation capacity: 0.112-0.185KgO2 / m3h oxygenation Power Efficiency: 4.46-5.19KgO2 / kwh exposure Air resistance: 180-280mmH2O [Setup] FIG. 1 Examination of installation and construction; 2 audit site pool size is consistent with the construction plans; 3 according to the situation and put a line drawing; 4 Press the line to fight the expansion bolt, install adjustable pipe support; 5 According to begin drawing pipe cutting size cutting; 6 intermediate intake supervisor position, will be supporting the four-way or on behalf of the three-way good bonding (Note: Be sure to smooth vertical and horizontal); 7 aerator on the drawings according to the location of the branch pipe actinomycetes, hole, hole size is generally 6 ~ 8mm, according to the specific type of aerator; (debris punctured must be clean, can not remain in the pipeline) 8 manifold on adjustable On the stent, and intake supervisor intermediate bonding together (note: the manifold hole must lay vertically upwards); nozzle links two sides of the interface 9 tube bends bonding interface manifold together. (Note: Be sure to smooth vertical and horizontal) 10 modulates the level of the whole pipe with an adjustable pipe support; adjustable pipe support nylon cable ties (11 bar on: the nylon strap without holes in the bracket of the card side buckle slot, and then find a iron bar into the square hole about 12mm nylon cable tie, the slight pressure to wear a); 12 in the branch pipe position perforated adhesive aerator spout (Note: Exposure scrubber spout must be straight up); 13 pending aerator spout after bonding firm (about 24 hours), and then install the aerator; 14 aerator and piping installed, to prevent the pipe connections leak , water to the aeration tanks should be placed around the upper part of 100mm, then the ventilation test, if there is the leak site and mark it should be repaired, to be fully qualified, you can officially put into use. 15 Note: ①, in order to prevent other jobs, such as welding sparks and civil construction and other damage to the aerator, aeration piping systems must be installed at the end of the civil engineering. ②, ABS nozzle can not polish bonding after bonding UPVC nozzle must be polished, aeration piping recommended ABS pipe. Usage and warranty] First, the product uses the environment is limited to the following conditions 1 Water temperature: 10 ~ 50 ℃ 2 quality: 3 conventional sewage water depth: ≤5m 4 air volume: ≤3m3 / h only two, run under the following conditions and the environment. 1 purchase not covered by the warranty, improper storage during stacking produce damage; rubber diaphragm 2 during installation scratch; 3 glue pollution rubber diaphragm; 4 random throw injury rubber diaphragm; 5 may arise in acid, alkali, viscous , a lot of oil present in the wastewater operation; aeration 6 factorial design layout is unreasonable, poor aeration air cleanliness and installation of pipe fittings and other causes exist garbage left uneven, not covered under warranty; 7 from the use, maintenance, damage caused by improper storage, or damage due to force majeure, disassemble, damage caused by services not covered under warranty. Users should be strictly in accordance with the instructions for use of the aerator using the product, beyond the range of my unit is not responsible for the warranty. |
Admin>>>
You are the 13409 visitor
Copyright © GuangDong ICP No. 10089450, Hebei-Hong Kong Environmental Protection Equipment Co., Ltd. All rights reserved.
Technical support: ShenZhen AllWays Technology Development Co., Ltd.
AllSources Network's Disclaimer: The legitimacy of the enterprise information does not undertake any guarantee responsibility
You are the 13409 visitor
Copyright © GuangDong ICP No. 10089450, Hebei-Hong Kong Environmental Protection Equipment Co., Ltd. All rights reserved.
Technical support: ShenZhen AllWays Technology Development Co., Ltd.
AllSources Network's Disclaimer: The legitimacy of the enterprise information does not undertake any guarantee responsibility